Item Description
| Planetary Gearbox | ||||
| GBR | 060 | 10 | S1 | P1 |
| Reducer Series Code | Measurement | Equipment Ratio | Output Shaft Sort | Reducer Backlash |
| GBR – High-Precision Right Angle Square Flange Output | 60mm 90mm 115mm 142mm | 1 Phase: 3 4 5 6 7 8 9 10 2 Stage: 12 15 16 20 25 28 30 35 40 forty five 60 70 80 90 100 |
S1 – Sleek Output Shaft S2 – Output Shaft With Important |
P1 – Decreased Backlash P2 – Standard Backlash |
| Sequence | Unit | GBR | Z(2) | |||
| Life time | % | 20000 | ||||
| Performance with Complete Load (3) | °C | 97 | 1 | |||
| 94 | 2 | |||||
| 0perating Temp (4) | -twenty five~+ninety | |||||
| Diploma of Protection | IP65 | |||||
| Lubrication | Lifetime Lubrication | |||||
| Mounting Place | Any | |||||
| Motor Flange | DIN 42955-N | |||||
| Product | Device | GBR060 | GBR090 | GBR115 | GBR142 | Z(2) |
| P1 Low Backlash P1 | arcmin | ≤5 | 1 | |||
| ≤7 | two | |||||
| P2 Common Backlash P2 | arcmin | ≤7 | 1 | |||
| ≤9 | two | |||||
| Nominal Input Speed (8) | rpm | 3000 | 2000 | |||
| Highest Input Pace (8) | rpm | 6000 | 4000 | |||
| Maximum Radial Load (5)(6)(9) | N | 1200 | 2400 | 4300 | 9100 | |
| Optimum Axial Load (5)(6)(9) | 1100 | 2200 | 3900 | 8200 | ||
| Torsional Stiffness | Nm/arcmin | seven | fourteen | twenty five | 50 | one |
| eight | 16 | 28 | fifty five | two | ||
| Bodyweight | Kg | two.one | 4.two | ten.5 | twenty.three | one |
| two.four | 4.nine | 11.2 | 21.five | two | ||
| Working noise (7) | dB(A) | 63 | 65 | 68 | 70 | |
(1) Ratios(=n in/n out)
(2) Variety of stages
(3) Is dependent on the ratio, n2=100rpm
(4) Referring to the center of the body area
(5) These values refer to a speed of the output shaft of n2=100rpm on duty cycle KA=one
and S1-mode for electrical equipment and T= 30°C
(6) Halfway together the output shaft
(7) Audio pressure amount distance 1m measured on idle working with an enter velocity of ni =3000rpm i=5
(8) Allowed functioning temperature should be held other enter speeds on inquiry
(9) Based on the essential output torque, radial and axial masses, cycle and essential storage daily life,
deviating or partly increased values are possible.
We advocate to carry out accurate dimensioning with CZPT or to seek the advice of Neugart in this regard.
FAQ
Q: How about your firm?
A: We are a gear motor manufacturing unit set up in 1995 and found in HangZhou town of china.
We have far more than 1200 workers. Our major merchandise is AC micro gear motor 6W to 250W,
AC small equipment motor 100W to 3700W, brush DC motor 10W to 400W, brushless motor10W to 750W,
drum motor 60W to 3700W, planetary gearbox,and worm gearbox,and many others.
Q: How about your good quality management?
A: From uncooked material to completed items, we have strict and full IPQC.
And the sophisticated test-ing device can assure of qualified products sent.
Q: How to choose a suited motor?
A: If you have gear motor pictures or drawings to show us,
or you explain to us thorough specs like volt-age, velocity, torque, motor dimension, the doing work design of the motor, needed lifetime and noise amount, and so forth.
please do not hesitate to allow us know, then we can propose a suited motor for every your ask for.
Q: Can you make the gear motor with customizing specifications?
A: Sure, we can personalize for every your ask for for the voltage, pace, torque, and shaft dimension and condition.
if you want additional wires or cables soldered on the terminal or want to include connectors, or capacitors, or EMC we can make it way too.
Q: What is actually your lead time?
A: Normally our typical common item will want ten-15days, a little bit lengthier for custom-made items.
But we are quite versatile on the direct time, it will rely on the specific orders.
Q: What is your MOQ?
A: If delivered by sea, the minimal purchase is a hundred pieces, if supply by express, there is no restrict.
Q: Do you have the merchandise in stock?
A: l am sorry we do not have the item in inventory, All merchandise are made with orders.
Q: How to get in touch with us?
A: You can send us an inquiry.
|
/ Piece | |
1 Piece (Min. Order) |
###
| Application: | Industrial |
|---|---|
| Speed: | Constant Speed |
| Function: | Driving, Control |
| Casing Protection: | Closed Type |
| Number of Poles: | 2 |
| Certification: | ISO9001, CCC |
###
| Customization: |
|---|
###
| Planetary Gearbox | ||||
| GBR | 060 | 10 | S1 | P1 |
| Reducer Series Code | Size | Gear Ratio | Output Shaft Type | Reducer Backlash |
| GBR – High-Precision Right Angle Square Flange Output | 60mm 90mm 115mm 142mm | 1 Stage: 3 4 5 6 7 8 9 10 2 Stage: 12 15 16 20 25 28 30 35 40 45 60 70 80 90 100 |
S1 – Smooth Output Shaft S2 – Output Shaft With Key |
P1 – Reduced Backlash P2 – Standard Backlash |
###
| Series | Unit | GBR | Z(2) | |||
| Lifetime | % | 20000 | ||||
| Efficiency with Full Load (3) | °C | 97 | 1 | |||
| 94 | 2 | |||||
| 0perating Temp (4) | -25~+90 | |||||
| Degree of Protection | IP65 | |||||
| Lubrication | Lifetime Lubrication | |||||
| Mounting Position | Any | |||||
| Motor Flange | DIN 42955-N | |||||
| Item | Unit | GBR060 | GBR090 | GBR115 | GBR142 | Z(2) |
| P1 Low Backlash P1 | arcmin | ≤5 | 1 | |||
| ≤7 | 2 | |||||
| P2 Standard Backlash P2 | arcmin | ≤7 | 1 | |||
| ≤9 | 2 | |||||
| Nominal Input Speed (8) | rpm | 3000 | 2000 | |||
| Maximum Input Speed (8) | rpm | 6000 | 4000 | |||
| Maximum Radial Load (5)(6)(9) | N | 1200 | 2400 | 4300 | 9100 | |
| Maximum Axial Load (5)(6)(9) | 1100 | 2200 | 3900 | 8200 | ||
| Torsional Stiffness | Nm/arcmin | 7 | 14 | 25 | 50 | 1 |
| 8 | 16 | 28 | 55 | 2 | ||
| Weight | Kg | 2.1 | 4.2 | 10.5 | 20.3 | 1 |
| 2.4 | 4.9 | 11.2 | 21.5 | 2 | ||
| Running noise (7) | dB(A) | 63 | 65 | 68 | 70 | |
|
/ Piece | |
1 Piece (Min. Order) |
###
| Application: | Industrial |
|---|---|
| Speed: | Constant Speed |
| Function: | Driving, Control |
| Casing Protection: | Closed Type |
| Number of Poles: | 2 |
| Certification: | ISO9001, CCC |
###
| Customization: |
|---|
###
| Planetary Gearbox | ||||
| GBR | 060 | 10 | S1 | P1 |
| Reducer Series Code | Size | Gear Ratio | Output Shaft Type | Reducer Backlash |
| GBR – High-Precision Right Angle Square Flange Output | 60mm 90mm 115mm 142mm | 1 Stage: 3 4 5 6 7 8 9 10 2 Stage: 12 15 16 20 25 28 30 35 40 45 60 70 80 90 100 |
S1 – Smooth Output Shaft S2 – Output Shaft With Key |
P1 – Reduced Backlash P2 – Standard Backlash |
###
| Series | Unit | GBR | Z(2) | |||
| Lifetime | % | 20000 | ||||
| Efficiency with Full Load (3) | °C | 97 | 1 | |||
| 94 | 2 | |||||
| 0perating Temp (4) | -25~+90 | |||||
| Degree of Protection | IP65 | |||||
| Lubrication | Lifetime Lubrication | |||||
| Mounting Position | Any | |||||
| Motor Flange | DIN 42955-N | |||||
| Item | Unit | GBR060 | GBR090 | GBR115 | GBR142 | Z(2) |
| P1 Low Backlash P1 | arcmin | ≤5 | 1 | |||
| ≤7 | 2 | |||||
| P2 Standard Backlash P2 | arcmin | ≤7 | 1 | |||
| ≤9 | 2 | |||||
| Nominal Input Speed (8) | rpm | 3000 | 2000 | |||
| Maximum Input Speed (8) | rpm | 6000 | 4000 | |||
| Maximum Radial Load (5)(6)(9) | N | 1200 | 2400 | 4300 | 9100 | |
| Maximum Axial Load (5)(6)(9) | 1100 | 2200 | 3900 | 8200 | ||
| Torsional Stiffness | Nm/arcmin | 7 | 14 | 25 | 50 | 1 |
| 8 | 16 | 28 | 55 | 2 | ||
| Weight | Kg | 2.1 | 4.2 | 10.5 | 20.3 | 1 |
| 2.4 | 4.9 | 11.2 | 21.5 | 2 | ||
| Running noise (7) | dB(A) | 63 | 65 | 68 | 70 | |
Worm gear reducer gearbox
Cheaper than planetary gearboxes In many cases, worm gear reducer gearboxes are a popular alternative to planetary gearboxes. A worm gear reducer gearbox is a mechanical device with vertical input and output shafts. This allows for very high reduction ratios. They are typically used in high-reduction situations such as machine tools.
Worm gears are cheaper than traditional gearboxes. They also have many benefits, including noise reduction. The output shaft of the worm gear reducer gearbox is almost 90 degrees from the motor input shaft, making it ideal for high-torque applications.
The worm gear reducer gearbox adopts an aluminum body, which is light in weight and high in operation efficiency. Additionally, they are available with hollow shafts and mounting flanges. In terms of initial cost, worm gear reducer gearboxes are cheaper than planetary gearboxes. In addition, they have better efficiency and longer service life.
Worm drives are also ideal for portable battery-powered lifting equipment. The high gear ratio of the worm gear ensures that it does not reverse drive. The worm gear has a spring-applied brake that holds the motor in place.
Planetary gearboxes are popular among industrial users. The efficiency of planetary gearboxes is important for practical applications.
The compact worm gear unit consists of a housing with an inner cavity. It has two side walls, one on either side of the front cover (13) and one on both sides of the rear cover (14). The front end cap is screwed onto the housing and the inner cavity is accessed through the rear end cap.
The compact worm gear unit can be configured to suit your application. They have many advantages, including saving space and increasing torque. The range includes single-envelope and double-envelope versions, available in a number of different power ratings. Additionally, they are IP65-rated, making them ideal for applications involving high radial or axial forces.
The compact worm reducer gearbox is a simple but effective worm drive. Its worm gear 16 meshes with the output shaft and rotates relatively stably. It also has a front-end cap and rear bearing. This enables the compact worm reducer gearbox to reduce vibration without damaging the output shaft.
Compact worm gear reducer gearboxes are ideal for many applications and offer high efficiency. The compact design means you can mount them on the motor’s flange or base. Its durable construction makes it ideal for a variety of industries. They are extremely durable and can handle high-pressure and washdown conditions. They also come standard with a synthetic shaft.
high efficiency
High-efficiency worm gear reducer gearboxes are ideal for applications that require precision, repeatability, and efficient performance. These reducer gearboxes are designed with state-of-the-art servo motor technology to provide tight integration and an angular backlash of less than two arc minutes. The reduction ratio can be lower if the application requires it.
Rising energy costs have led to an increased focus on the efficiency of drives. In response to this, manufacturers have increased the efficiency of worm gear reducer gearboxes through a number of technical improvements. By minimizing losses from rolling and sliding friction, worm gear reducer gearboxes are more efficient than their counterparts.
The high-efficiency worm reducer gearbox is simple in design and has the characteristics of a compact structure, high-speed ratio, low power consumption, and self-locking. Other advantages of these reducer gearboxes include low noise and long service life. Many also have built-in control systems that allow manual and remote adjustments. They also feature automatic shutdown protection and thermal protection.
High-efficiency worm reducer gearboxes can be used for mechanical acceleration. The input hypoid gear is usually made of steel, while the output hypoid gear is usually made of bronze. Bronze is a soft metal that is good at absorbing shock loads. However, bronze requires work hardening to achieve optimum hardness. For large worm gears, this process can take 300 to 550 hours.
low clearance
A low-clearance worm reducer gearbox is a device used to adjust the speed of a rotating shaft. It uses a worm gear consisting of two members. One worm is at one end of the shaft and the other is at the other end. Both worms are screwed into the synchronous drive structure.
Low clearance worm gear reducer gearboxes can be produced on conventional worm gear production lines without overlapping investments. These units are usually made of soft rubber. Also, they are relatively quiet in operation. These machines are designed so that they are suitable for use in elevators. The softer material in the worm gear also helps absorb shock loads.
The tooth profile of the worm gear is designed to change with the axial movement of the worm. Worms have thinner right teeth and thicker left teeth. As the worm moves to the right, its teeth mesh with the worm gear, reducing backlash.
There are many different types of worm gears. The design of gears depends on many factors, including backlash, thermal design, friction factors and lubrication. Worm gears are made of several different materials. Some different types of materials used in worm gears require special lubrication.
quieter
The quieter worm reducer gearbox is designed to reduce the noise level of the rotating gear motor. The device has more gear teeth in meshing contact with the gears, which helps it run more quietly. In addition to being quieter than other transmissions, it’s also less expensive than its counterparts.
Worm gearboxes can be used for different applications, but they are not as efficient as helical gearboxes. Worm reducer gearboxes are cheaper but less than 90% efficient. Higher gear ratios reduce efficiency, so worm gear reducer gearboxes are better suited for applications that require low-speed torque. The cost of buying a worm gearbox will depend on the horsepower and gear ratios required.
Worm reducer gearboxes are also more comfortable to use than planetary gearboxes. They don’t vibrate and heat up quickly, making them an excellent choice for low to medium horsepower applications. Worm gear reducer gearboxes can be upgraded to improve their performance by combining with other gear trains or gearboxes.
easy to replace
An easily replaceable worm gear reducer gearbox can save you a lot of money. A worm gear reducer gearbox is part of a chain drive and allows you to change gear ratios quickly and easily. Worm gear reducer gearboxes can be easily replaced in a number of ways. It’s a good idea to read the manufacturer’s manual before replacing a worm gear reducer gearbox. Make sure you have the instructions available so you can refer to them in the future.
Worm gear reducer gearboxes offer many advantages, including long service life and low noise. They are also designed with a 90-degree output shaft for easy installation. Another advantage of these gear reducer gearboxes is that they can be used with both solid and hollow output shafts. This means less maintenance and downtime.
Worm gear reducer gearboxes are widely used. Most gear manufacturers have large inventories. Worm gears also have uniform mounting dimensions. Dimensional consistency means you don’t have to worry about matching the shaft length and diameter to the worm gear. You can easily find a replacement worm gear reducer gearbox for your equipment.
When replacing the worm gear reducer gearbox, check the lubricating oil recommended by the machine. If not included, use original gear oil. Be sure to follow the manufacturer’s instructions carefully.
editor by CX 2023-04-13